olivasmith546's blog

Brother Printers are among the most preferred printer manufacturers present in the market. These printers provide the users with all the required assistance in their day to day functioning. One issue which the users come up is when they are unable to connect their Brother HL-2270DW printer to the Wi-Fi. When faced with such an issue, the users can use the automatic wireless mode such as AOSS or the Wi-Fi protected setup configuration for your Brother printer. The users can learn more about this by going through this entire blog. The users can also avail assistance from trained professionals by connecting with Brother Printer customer service number. 

Ways to connect Brother Printer HL-2270DW to Wi-Fi using the Wireless setup?

The users can easily follow the below-given steps to connect their HL-2270DW Brother printer with W-Fi:

·        While trying to set up the Wi-Fi, simply ensure that the printer is close to the router or the access point.

·        Then the users need to plug the power cord in and switch the device on.

·        Further look for AOSS or WPS button and then press it down for a few seconds.

·        Now reach out to the back of the printer device and press the wireless setup button for about 2 seconds. The users must ensure that they do not press it for more than 3 seconds.

·        When you do so, the PIN method for the Wi-Fi Protected Setup mode would change.

·        You would also have to wait for another 5 minutes for this mode to clear.

·        You might also have to turn off the printer completely and initiate the process all over again.

Before Configuring the Brother Printer

There are various points that you require to confirm before configuring and installing the Brother HL-2270DW printer. These points are as stated below:

·        Initially check if the router or access point supports the AOSS or WPS.

·        Also keep all the initial requirements for installation-ready such as SSID, Passkey, Network Name. You should also be able to visualize this when you turn the router towards its side.

·        The users must also check the documentation associated with the WLAN Router.

·        It is vital that the users ensure that there is no interference to the functions of the WLAN Access Point or Router.

·        If you have also configured multiple SSIDs to your LAN, then each of these would use different encryption and authentication methods.

·        It is crucial that the system and the Brother printer have the same network which would ensure smooth communication and setup.

If the users wish to attain more information to connect their Brother printer to the Wi-Fi, then they can promptly connect with Brother Printer technical support number. This service functions all around the clock and is accessible throughout the day using a toll-free number. Using this toll-free number, the users can easily connect with trained professionals who are capable are solving all the issues which the users might come across.

Source URL: Connect Brother HL-2270DW Printer to Wi-Fi

Brother printer is considered to be one of the most reliable printers available in the market. It has been serving users with some impressive features and has always ensured customer’s satisfaction. The duplex feature in printers allows you to take printouts on both sides of a sheet automatically. It reduces your printing cost to some extent. But at times it happens that your brother printer does not allow duplex printing, which affects your budget again. Once you go through this article, you will get to know the reasons behind this error and some troubleshooting steps have also been provided to make it easy for you to overcome this problem. By following this article, you will be able to fix this problem, and duplex printing will be enabled again. You can also connect with experts at Brother Printer  phone  number to avail assistance from the technical experts who provide you with a detailed and step by step solution to your problem.

Probable causes of Brother printer duplex not working:

If you are stressed because your brother printer duplex feature is not working, you just have to relax because once you get to know the reasons for this problem, the issue will be quickly resolved. Have a look at some of the main causes of this error:

ØSome users are encountering this issue on their Macbook pros and not anywhere else. So the problem must be with your Mac driver

ØIncompatibility between the printer driver and the operating system you are using can also cause this error

ØIf you have done a recent update, it can prevent duplex printout

ØIt can also occur when you have installed a third-party print service along with Brother printer software on your PC.

ØIf you have a corrupt folder on your PC, it can also cause this error.

Methods to fix Duplex printing problem in Brother printer

If your Brother printer’s duplex feature is not working, you can go through the steps provided below:

ØMake sure that the Duplex feature is installed in your printer: If you want to get dual-sided printouts from your printing machine, you will have to verify if the duplex printing option is enabled or not.

ØEnsure that you are using an updated version of Brother printer driver: The setup of the printer driver is crucial to print both front and back of the pages. Your device will stop this if you are using outdated software. You need to download and install the latest software to activate the duplex feature.

ØYou also need to check the Page setup and Paper settings in the printer:There are some minor details every customer should check, such as the paper type and page setup settings. You can do it by visiting the ‘Printer Settings’ option.

These are the few solutions which can fix your issue very soon. But if you face any trouble incorporating these steps, you can get in touch with Brother Printer  technical support number and ask the technical masters to assist you properly. You will be provided with the best possible solution in absolutely no time.

Source URL: Brother Printer Duplex Not Working

It can be quite frustrating when you have to transfer a file to the computer that is connected to your Brother Printer, only because you have to take a printout. However, if you are lucky enough to have a Brother Wireless Printer, you can connect your printer directly to your computer using the Wi-Fi network. This article will give you an overview of the steps you need to follow to set up your Brother Wireless Printer and connect it to your Windows device. Since it is possible that different Brother Printer models may have different setup steps, you can call the Brother Printer  contact number and consult an experienced printer expert to get a better idea about the process you need to follow for your specific printer.

Steps to set up a Brother Wireless Printer in Windows

Before you think of setting up can connectin your Brother Wireless Printer to your Windows device, you need to make sure you know the wireless network settings of your router or access points. Once you know the required network settings, you can follow the steps given below to set up your printer and connect it to your Windows computer:

·        Step 1: Open the Windows search menu by pressing “Windows + Q.”

·        Step 2: Enter the word “printer” in the search field and click ‘Enter.’

·        Step 3: Scroll down the list and click the ‘Printers & Scanners’ section.

·        Step 4: Press the power button and turn on your Brother Wireless Printer.

·        Step 5: Use the net settings and connect your printer to your Wi-Fi network.

·        Step 6: Click on the option that reads ‘Add a printer or a scanner.’

·        Step 7: Go through the list of devices and look for your Brother Printer.

·        Step 8: Select the Brother Wireless Printer and click ‘Add device’ to complete the setup process.

In case you do not see your Brother Wireless Printer in the list of devices, there is no need to panic. You can simply select the ‘The printer that I want isn’t listed’ option and follow the prompts. You need to makes sure you click the ‘Add a Bluetooth, wireless, or network discoverable printer’ option and see that your printer and Windows computer are connected to the same Wi-Fi network.

In case you have any trouble completing the setup steps mentioned in this article, you can always call the Brother Printer  technical support number and ask for additional technical assistance. Whether you face an error in the setup process or if you encounter a more complex software glitch related to your Brother Printer, experts are available 24 hours a day to respond to any query you may have. You just need to call the support number, and you will get a step-by-step guide on how to fix any Brother Printer error.

Read More: Brother Printer  helpline number

Source URL: How to set up a Brother Wireless Printer For Windows

Use the next generation printing technology and print in faster speed, excellent quality with Brother Printer. Brother GTX includes the X factor that makes the users never sacrifice for print quality. Imbibed with cutting edge technology, print captions, images, and graphics on garments and make a style statement. With an incredible color gamut and the top-notch print quality, opt for versatile patterns and abstracts and print over zippers, pockets, hems and more. Use the Brother GTX to expand your horizon. Wishing to know more about it? Interact with the techies at Brother Printer  technical support for the same

Have a look at the different features of Brother GTX printing:

ÌAvailability of 2 Print Heads (CMYK and W)

ÌPrint in single as well as multiple modes for CMYK, under the base, and highlight for white

ÌPrint area ( 16 X 21 inch)

ÌPrint CMYK with the help of white ink

Ì1200 X 1200 DPI resolution

Why should you opt Brother GTX for garment printing?

ØReplace technology with the long hours of toiling and needle techniques. With this feature, it becomes effortless for a person to create amazing designs on T-shirts and stuff.

ØWork with a wide range of color spectrum and choose the design as per your needs.

ØWorried about printing texts and images on T-shirts with zippers and pockets? Brother GTX makes it so easy to print over intricate garments seamlessly

ØCost-effective and doesn’t require much labor. A single person can take up projects and deliver them in the correct time

ØWant to reprint one design on different garments? Do that quickly and easily

ØAchieve faster outputs and work parallel with the market trends

ØWish to make a style statement by wearing a T-shirt with the caption that defines your personality? Do not hover around in the market searching for one. Opt for Brother GTX printing and design the T-shirt as you like.

How to use the Brother GTX for garment printing?

üThinking to print with white ink? Apply the right amount of pretreating as per the garment. Use the Brother pre-treatment machine for the same. Once done, secure the solution with either a press or a dryer

üDecide your artwork which you want to imprint on the garment and load it into the Graphics Lab software. With this software, you can edit and change the position of the image, add texts and subtexts and make required changing

üOnce done keep the desired garment on the flat surface of the printer

üAfter that keep the printer garment underneath the heat press to secure the print and to make it more visible and effective

If you want to know more about this fantastic technology, you can communicate with the experts by dialing Brother Printer  customer support number. Interact with the techies and gain insight.

Source URL: Brother GTX for the garment printing

Brother printer is one of the trusted printers that has been serving the users with their needs of printing and helps them in  their complex assignment regarding printing tasks. It has the most advanced and unique features that make it easy for you to access high-quality prints easily. Now if you need to connect your printer to the wireless device, you can do that with some easy steps. You can also contact Brother Printer  tech support and get the easy support and valuable response, but you can also get the perfect solution with the steps mention below. You need to follow this blog till the end to know the easy process of setting the wireless router to the Brother printer.

Before you start the process of setup wireless network:

You need to find the wireless network settings of your wireless router and check these settings below:

·        Network name (known as SSID or ESSID)

·        Network key (Known as password, security key or encryption key)

·        You can find these settings by going to the base or side of your router or access point.

·        Check out the documentation mention with your wireless router or access point.

Easy process to make the wireless connection on Brother printer:

·        First of all, you need to confirm the wireless router or access is completely set up.

·        Try to get the SSID or find the name of the wireless network and wireless network key.

·        You can get this information from your network administrator or internet provider.

·        Now put  the Brother printer closer to the router and turn on the printer.

·        Go the menu and choose the network option and press the ‘OK’ button.

·        You will get the setup wizard there and press ‘OK.’

·        Press the upside button and choose your network there, followed by ‘OK.’

·        Provide your password and click on ‘OK.’

·        It will print the WLAN report, and you will see the indicator light up on the screen.

·        This denotes that wireless setup has completed on your Brother printer.

·        Now if you need to download the driver, go to the web browser.

Get customer support for further solution:

These steps will surely be helping you to guide you to set the wireless network, but in case you are not getting the right direction or getting confused so you can contact at Brother printer customer care number anytime during the work process and get the complete satisfactory answer with the solution. You will get a prominent solution with permanent fixation by the trusted and experienced experts of Brother printer.

Source URL: How to setup Brother Printer using a wireless network

When it comes to Brother printer, it becomes imperative that you clean the paper pick up roller occasionally to avoid any malfunctions or troubles. This will ensure that you do not face paper jam troubles in the future. If the pick-up rollers are correctly cleaned, then you can be rest assured that the papers will get feeded into the tray correctly and when the print command is given, it will come smoothly without getting stuck. You can read this blog until the end and understand the cleaning procedure. Sometimes it can also require a technical expert to help you with the same, and if you wish to avail that, you can always dial Brother Printer tech support. You must also get it serviced annually in order to avoid troubles in the future.

The process to clean the Brother Printer Pick up roller:

·        Switch off the Brother printer and remove the power cord from the main switch

·        If the paper flap, where you insert the papers is open, you need to close it and also close the paper support.

·        Now pull out the paper tray from the machine

·        Take a moist linen cloth          and damp it with water and clean the Base Pad 1.

·        If you have the printer with model number MFC-J680DW/MFC-J880DWMFC-J885DW, then you need to clean the Base Pad 2 as well.This is the photo bypass tray and wipes it with the same linen cloth.

·        After cleaning it, take a dry cloth and wipe it on the base pad to soak the moisture

·        Now again take a moist cloth and start rotating the paper pick up roller and clean it with the fabric. Make sure that no point gets missed

·        After it is cleaned, remove all the moisture with the dry cloth.

·        Now insert the paper tray back and fix it securely.

·        Connect the power cord back again.

·        Switch on the printer and see whether the issue has been resolved or not.

This can be a complicated procedure, especially for those who have no technical knowledge about the printer’s equipment. Instead of implementing the given method in a faulty manner, it is suggested that you take help from the professional executives by dialing the toll-free number at Brother Printer  customer care number. Doing this without additional help, especially when you are not technically sound can lead to future issues and can worsen the situation.

It is suggested that you take help from the professional executives by dialing the toll-free number at Brother Printer Customer Support number.

brother printer support number, brother printer customer care number, brother printer technical support number, brother printer tech support number, brother printer customer support number.

Source URL: 1-866-429-4641 Clean Brother Printer Paper Pick-up Roller

Brother printer is a highly extensive printing device which is available in the market. They provide the users with the best printing services, which is accompanied by top quality fax and scan features. Even when the users attain optimum facilities while using Brother printer, there are certain issues which also come up. Malfunctioning is a common scenario which most of the electronic devices come across. One such issue is the error code 30 which is often seen on Brother Printer. The users can understand more in detail about this issue by going through this blog. These users also have the alternative option of connecting with Brother Printer support phone number to avail professional assistance regarding the same issue.

Reasons which cause Brother Printer Error Code 30

Some of the most common reasons for facing the error code 30 on your Brother Printer is as given below:

·        When the printer head carriage has failed to come back to its home position, which is to the far right of the unit.

·        When the mechanisms located on both sides of the carriage are out of place.

·        When the cartridge cover is not locked accurately in their place.

Ways to fix Brother Printer Error Code 30

If you wish to solve the issue of Brother Printer Error Code 30, then you would have to take up some simple steps which would help you solve the issue easily. The steps that you would have to undertake are as given below:

Procedure 1:

·        You would have to open the cover of the printer using the tabs which are given on the printer. Buttons can be found on the left and right side of the machine.

·        Now you would have to shift the print head to the center of the machine.

·        You would now have to check and confirm that no piece of paper, staple or paper clip is found inside the machine.

Procedure 2:

·        The user would now have to hold the scanner cover by using the tabs of the cover of the printer. It is placed on the left and right-hand side of the printer.

·        Now slide the print head over to the right side under the cover to confirm that you have cleaned the whole encoder strip of the machine.

·        Further by using a lint-free cloth, you would have to tightly confine the encoder strip on both sides and scour the cloth down the strip from one end to the other, a minimum three times.

Procedure 3:

·        The users would have to check the position of the encoder strip and find whether it is accurately placed or not.

·        If you find any discrepancy, open the printer and then reinsert the strip again.

·        Finally, it is advised that you reset your printer and then take a text print to analyze the quality of the print.

If you find that you are unable to solve this issue using the above-given steps, then it is advised that you promptly get connected with Brother Printer  customer support phone number.This service can be accessed throughout the day and is completely free of charge.

Brother Printer Error code 71 is displayed as ‘Print Unable 71’ on the printer display screen and is associated with the mechanical malfunction of the printer. This error code is related to the laser unit polygon motor. The polygon motor runs on the power of 20 to 40,000 RPMs. It depends on the version of the machine that you are using. You must first understand what the actual reason behind this error is. The polygon motor runs at its set operating speed depending on the machine that you are using. If it is not able to attain its acquired speed in the set amount of time, Print Unable 71 error starts displaying on the unit. Sometimes the motor gets jammed and needs a quick fix. This blog will help you to solve the issue if you intend to do it manually. Rest, if you acquire remote help and technical assistance, dial Brother Printer  technical support phone number and have a word with the techies.

Manual solution to fix Brother printer error code 71

ØSwitch off the printer and unplug it from the primary power source

ØOpen the rear door and remove the polygon motor from the bushing

ØApply some lubricating oil on to the motor and clean it.

ØIf you find that the motor has wearied off, kindly replace the unit. (The best way to judge that is when the unit becomes too noisy or gets locked)

ØOnce done, insert back the motor and secure its place.

ØNow connect back the printer to the system.

ØGo to the official Brother Printer website and look for the latest firmware and install it in the system. The printer must be working on correct settings

ØUpdate firmware and once done, switch off the printer and after 20 seconds, switch on the Power button again.

ØIf you find that the date and time are appearing on display, the issue is finally resolved.

The Brother printer can remain powered off for up to 4 days and still it won’t lose the faxes in the memory. But if the error message keeps on popping, again and again, it is suggested that you transfer the faxes to another fax machine. Make sure that the user settings are appropriately configured. If by chance, this error keeps on reoccurring, it is advised that you consult the technicians at Brother Printer support number. They will help you to resolve the error. The number remains in service 24*7 and is toll-free.

Source URL: Resolve Brother Printer error code 71

The users of Brother Printers come across the error code 48 when there is some issue with the printer head cable. The users encounter this issue when the encoder strip is untidy. When the printer faces this issue, the user will come across numerous errors. This would mean that you would have to solve the issue at the earliest to get back to the smooth functioning of the printer. The users can get a clear understanding of this issue by having a look through this blog. The users would also have the option of connecting with Brother Printer  customer service number.

This is an issue which the users can come across at any time while using Brother Printers. Some error codes that you would face when you have this issue on your printer is as given below:

·        Brother Printer Unable to Print 8f

·        Unable to scan

·        Brother Printer unable to clean and many other printer functionality issues

Effective ways to solve the issue of error code 48

This is one of the most common issue that the users come across while using Brother Printers. The users can effectively solve this issue by undertaking the below-given steps:

Solution 1: Check for Brother Printer Paper Jam or Paper Scraps

·        Firstly, you would have to disconnect your printer from the power source and the computer system.

·        Then you would have to remove the scanner cover and have a look inside the machine.

·        Further examine whether there is paper jammed inside the device, also ensure that there no debris collected inside the printer device.

·        You would have to make sure that the paper is not blocking the print head. Tilt your printer left and right to check whether there is any kind of debris inside.

·        If you find that the printer head is to the left side, manually move it to the middle. Clear the encode strip and close the scanner cover and reconnect the power cord.

·        If the printer head is found to be towards the right, reconnect the power cord. When the LCD displays the ‘Cover is open’ message, press and hold the Exit button for 5 seconds. When you see that the print head has moved back to the middle, remove the power cord.

Solution 2: Manually clean the Encoder Strip

·        Start by removing all the power cables from the printer.

·        Now, remove the Scanner cover and then look for the Encoder strip of your printer.

·        You would now have to use a dry lint cloth to clean out both sides of the Encoder strip.

·        Once you are done cleaning the Encoder strip, close the scanner cover.

·        You can now reconnect all the power cables back to the printer device and then check whether the error has been solved.

These are the most effective steps that the users can use to solve the Brother Printer Error Code 48. If you face any difficulty in enacting the given steps, you can then connect with Brother Printer  technical support number to avail professional assistance.

Source URL: Troubleshoot Brother Printer Error Code 48

Brother printer is undoubtedly one of the most efficient and advanced printing devices that can make the printing process quite easy by ensuring the printing quality as well. Now if you face the problem as you Brother Printer is offline on windows 10, then you don’t need to worry because you are at the right place where you will be getting the most prominent solution with easy steps that can fix your problems within minutes. However, you can also contact to Brother Printer  tech support to get the expert solution and guidance.

Easy methods to fix the Brother Printer offline on windows 10 issue:

There several methods that can easily fix the issue but here you will find the most common solutions that will not take any deep techniques and professional approach. Now without wasting time further, you can follow these methods to solve your issue:

1.    Check the printer connection:

·        Check all the cables through your printer is connected, if you find any loose connection make them fixed.

·        Check the Ethernet port as well and make sure that is connected well with the network.

·        If you are using the wireless network check the Wi-Fi connection and router network as well.

2.    Test the printing status:

·        By pressing the windows+, I key from your keyboard you will get a new window

·        Now select the devices option there

·        Navigate the related settings and click on “devices and printers” option

·        When you find the devices right click on the icon with a green mark

·        Now select the “See what’s printing” option

·        Then right click on the grey colored option

·        Now choose the option “set as default.”

·        Select the “Printer” option and remove the tick marks to the pause printing and use offline printer boxes.

3.    Review the printer spooler services

·        Press the windows+R button in your keyboard and get the search bar

·        Now type services.msc in the box and press enter

·        Find print spooler option in the list and check the status “Running.”

·        If you are unable to see the status, then right click on the option and select start

·        Now again right click on print spooler and select restart

·        Then you can close the window

4.    You can update the printer driver

·        Press windows+I button and select the devices option

·        Then click on “Devices and printers.”

·        Hit a right click on Brother Printer

·        Then select the option of remove device

·        Permit the dialog box and press yes

·        Now you can update the printer driver easily.

Get customer support for further assistance:

In case all these methods failed to solve your issue or you area unable to perform these methods easily you should call at Brother Printer  customer care number and get the most professional approach to solve your issue easily.

Source URL: Brother Printer Offline on Windows 10